You are not logged in.

The 1st Filipino PC Modding Site

#9 2009-05-24 17:37:37

robo
Member
From: Cebu
Registered: 2008-12-04
Posts: 110

Re: How to build a Plastic Heat Bender & How to bend Plastic

Sirs, meron na kayong tested DIY sa acrylic bending, paki post naman.


Measure twice, cut once.

Offline

2009-05-24 17:37:37

dremel
pcModz Bot
Registered: 2015-04-29
Posts: 8

Re: How to build a Plastic Heat Bender & How to bend Plastic



Online

#10 2009-05-25 09:44:57

beetoy
Member
From: Angeles City, Philippines
Registered: 2009-05-05
Posts: 64

Re: How to build a Plastic Heat Bender & How to bend Plastic

robo wrote:

Sirs, meron na kayong tested DIY sa acrylic bending, paki post naman.

Boss, hindi ko alam kung ano tawag dito hehehe. Pero kung maliit lang naman ang mga ibbend ninyo na acrylic, pwede na yung oven hehehe.

Ito yung ginamit ko sa pagbend ng acrylic sheet na pinagtakip ko sa likod ng ODD ko.


DSCF4854.jpg

DSCF4840.jpg



Pero ang problem nito ay kung mahaba yung ibbend. Kaya sana pashare naman din sa mga nakagawa na ng DIY na acrylic bender.

Last edited by beetoy (2009-05-25 15:48:39)


beetoy.jpg

Offline

#11 2009-05-25 22:46:07

blackmoly
Member
From: cavite
Registered: 2009-03-30
Posts: 27

Re: How to build a Plastic Heat Bender & How to bend Plastic

^ i have seen those heating elements being sold @ raon with different sizes and shapes...


EnDLeSs

Offline

#12 2009-06-12 18:45:12

robo
Member
From: Cebu
Registered: 2008-12-04
Posts: 110

Re: How to build a Plastic Heat Bender & How to bend Plastic

Here my working DIY on this.  I used nichrome wire and a generic PSU.;)

007cfn.jpg

008afq.jpg

009gso.jpg

013dpj.jpg

014anb.jpg


Measure twice, cut once.

Offline

#13 2009-06-13 23:51:47

kitaswandi
Moderator
From: Tanay,Rizal
Registered: 2009-01-24
Posts: 47

Re: How to build a Plastic Heat Bender & How to bend Plastic

nice you got there sir robo..

I have that one too on my shop, 1 15" and 1 40" in size.
My bender heater (nichrome) are coiled and the highest wattage is 2200w.

Last edited by kitaswandi (2009-06-13 23:52:36)


Unleashing my fullest potential....

Offline

#14 2009-06-17 14:32:34

beetoy
Member
From: Angeles City, Philippines
Registered: 2009-05-05
Posts: 64

Re: How to build a Plastic Heat Bender & How to bend Plastic

Where can we buy these nichrome wire? Is it safe to use? I am a newbie also in this item. Thanks sir Robo and sir Kitaswandi for your contribution. Hopefully with this tips, I will no longer use our oven. big_smile


beetoy.jpg

Offline

#15 2009-06-20 10:06:42

shamrage
Member
From: Sitio Pajo, Brgy Napnud
Registered: 2007-06-26
Posts: 261

Re: How to build a Plastic Heat Bender & How to bend Plastic

@robo Can you post some guidelines how to make this bender? Are you using 12v?

Offline

#16 2009-06-24 06:08:22

robo
Member
From: Cebu
Registered: 2008-12-04
Posts: 110

Re: How to build a Plastic Heat Bender & How to bend Plastic

I will make a guide on DIY bender later.  I jusst need to redo my bender, pangit kasi.:)

Just stretch the bended nichrome wire. Attach the the other end to the black wire of your molex, the other end to yellow. 12v input.


Measure twice, cut once.

Offline

Similar Topics Replies Views Last post
6 10145 2015-08-14 00:09:33 by Chriskey2015
1 2448 2013-01-19 19:28:15 by Neurotoxic
Patti... the ghetto case build by gabriel_d7  [ 1 2 ]
8 10749 2010-05-11 09:30:21 by Papang
2 3629 2010-03-13 13:59:55 by doki
Chipset Heat Issue by gabriel_d7
7 5574 2009-11-05 00:03:30 by gabriel_d7

Board footer

pcModz Ph © 2007 - 2016 All Rights Reserve.