You are not logged in.

The 1st Filipino PC Modding Site

#17 2009-06-24 08:17:06

beetoy
Member
From: Angeles City, Philippines
Registered: 2009-05-05
Posts: 64

Re: How to build a Plastic Heat Bender & How to bend Plastic

Sir Robo, where can we buy this nichrome wire? Thanks smile


beetoy.jpg

Offline

2009-06-24 08:17:06

dremel
pcModz Bot
Registered: 2015-04-29
Posts: 8

Re: How to build a Plastic Heat Bender & How to bend Plastic



Online

#18 2009-06-24 16:44:15

robo
Member
From: Cebu
Registered: 2008-12-04
Posts: 110

Re: How to build a Plastic Heat Bender & How to bend Plastic

@ beetoy

Available yan sa mga electronics store.


Measure twice, cut once.

Offline

#19 2009-06-25 08:05:07

beetoy
Member
From: Angeles City, Philippines
Registered: 2009-05-05
Posts: 64

Re: How to build a Plastic Heat Bender & How to bend Plastic

@Robo,

Thanks sir. Will try one out based from your set-up.


beetoy.jpg

Offline

#20 2009-06-25 18:01:43

doki
Site Admin
From: Philippines
Registered: 2007-06-20
Posts: 586
Website

Re: How to build a Plastic Heat Bender & How to bend Plastic

robo wrote:

I will make a guide on DIY bender later.  I just need to redo my bender, pangit kasi.:)

Just stretch the bended nichrome wire. Attach the the other end to the black wire of your molex, the other end to yellow. 12v input.

Is there a min/max length? or any length will do?

Thanks


I only drink diluted water.

Offline

#21 2009-06-27 10:46:32

robo
Member
From: Cebu
Registered: 2008-12-04
Posts: 110

Re: How to build a Plastic Heat Bender & How to bend Plastic

Sir doki, 1 foot long lang ang na try ko that works. I dont know if kung mas mahaba ang wire kung gagana pa ba.  Sibukan ko ang buong nichrome wire na coiled pa, hindi umiinit, kailanga yata mas mataas na wattage.


Measure twice, cut once.

Offline

#22 2010-11-09 22:49:07

lou76
Member
From: pasig city
Registered: 2010-11-09
Posts: 1

Re: How to build a Plastic Heat Bender & How to bend Plastic

doki wrote:

This video segment will show you how to build a plastic line bender using BriskHeat Strip Heater, so that you can bend plastic at home.

[youtube]http://www.youtube.com/watch?v=ZkjsPrWT0Ic[/youtube]

Saan po nakakabili ng materials na ginamit sa video or any alternative materials? available po ba sa atin yun BriskHeat Strip Heater? TIA

Offline

#23 2011-05-20 13:46:00

doki
Site Admin
From: Philippines
Registered: 2007-06-20
Posts: 586
Website

Re: How to build a Plastic Heat Bender & How to bend Plastic

Hi Lou,

Take a look on robo's post smile You can get some idea how to create a DIY bender. Nicrome wires usually available on electric and electronics shops.

link:
http://www.pcmodz.info/viewtopic.php?pid=1431#p1431


I only drink diluted water.

Offline

Similar Topics Replies Views Last post
6 10145 2015-08-14 00:09:33 by Chriskey2015
1 2448 2013-01-19 19:28:15 by Neurotoxic
Patti... the ghetto case build by gabriel_d7  [ 1 2 ]
8 10749 2010-05-11 09:30:21 by Papang
2 3629 2010-03-13 13:59:55 by doki
Chipset Heat Issue by gabriel_d7
7 5574 2009-11-05 00:03:30 by gabriel_d7

Board footer

pcModz Ph © 2007 - 2016 All Rights Reserve.